Dell™X200ServiceManual Before You Begin Preparing to Work Inside the Computer Recommended Tools Computer Orientation Screw Identification Syste
9. Move the display assembly to an upright position and pull it up out of the bottom case. Back to Contents Page 1 signal cable 2 inverter
Back to Contents Page Cooling Fan Dell™X200ServiceManual Removing the Cooling Fan 1. Remove the battery. 2. Remove the keyboard. 3. Remo
Back to Contents Page Hard Drive Dell™X200ServiceManual Removing the Hard Drive 1. Remove the battery. 2. Remove the keyboard. 3. Remove
Back to Contents Page Keyboard Dell™X200ServiceManual Removing the Keyboard 1. Remove the battery. 2. Remove the six M2 x 4-mm screws label
4. Pry up the keyboard locator tab, and the keyboard pops up. 5. Pull the keyboard a small distance toward the front of the computer to release
2. Ensure that the ZIF connector is open by pulling the ZIF connector tabs toward the back of the computer. 3. Press the keyboard flex cable into
Back to Contents Page Keyboard Tray Dell™X200ServiceManual Removing the Keyboard Tray 1. Remove the battery. 2. Remove the keyboard. 3.
2. Replace the keyboard tray. 3. Reinstall the seven M2 x 4-mm screws that secure the keyboard tray to the system board. Back to Contents Page
Back to Contents Page Modem Daughter Card Dell™X200ServiceManual Removing the Modem Daughter Card 1. Remove the battery. 2. Remove the keyb
Back to Contents Page Battery Latches Dell™X200ServiceManual Removing the Battery Latches 1. Remove the battery. 2. Remove the keyboard.
Back to Contents Page Palm Rest Dell™X200ServiceManual Removing the Palm Rest 1. Remove the battery. 2. Remove the keyboard. 3. Turn the
Back to Contents Page
Back to Contents Page Pin Assignments for I/O Connectors Dell™X200ServiceManual Pin Assignments for the Computer Pin Assignments for the X200
Pin Assignments for the X200 MediaBase Docking Connector 2 TPB- 3 P12V 4 GND 5 TPB+ 6 TPA+ Pin Signal Pin Signal 1 DCK3_DOCK_IN2 51 P3.3V_LAN 2 KBC
PS/2 Connector USB Connector IEEE 1394 Connector 39 PIO3_PD(6) 89 USB3_P5- 40 FDD3_TRK0 90 LAN3_RX- 41 PIO3_PD(7) 91 NC 42 FDD3_RDATA 92 NC 4
Serial Connector Parallel Connector Video Connector 3 TPA- 4 TPA- Pin Signal Pin Signal 1 DCD 6 DSR 2 RXDA 7 RTS 3 TXDA 8 CTS 4 DTR 9 RI 5 GN
Back to Contents Page 7 GND 15 CLK_DDC2 8 GND
Back to Contents Page Reserve Battery Dell™X200ServiceManual Removing the Reserve Battery 1. Remove the battery. 2. Remove the keyboard.
Back to Contents Page Speakers Dell™X200ServiceManual Removing the Speakers 1. Remove the battery. 2. Remove the keyboard. 3. Remove the
Back to Contents Page System Board Dell™X200ServiceManual Removing the System Board 1. Remove the battery. 2. Remove the keyboard. 3. Re
Back to Contents Page Battery Dell™X200ServiceManual Removing the Battery 1. Ensure that the computer is turned off, suspended in a power mana
3. Reconnect the status light (LED) cable to the system board ZIF connector. 4. Reinstall the four M2 x 4-mm screws that secure the system board
Back to Contents Page System Components Dell™X200ServiceManual Back to Contents Page NOTICE: Only a certified service technician should
Back to Contents Page Memory Module and Mini PCI Card Dell™X200ServiceManual Memory Module Mini PCI Card Memory Module Removing the Memory M
Replacing the Memory Module 1. Ground yourself and install the new memory module: a. Align the notch in the module with the slot in the center of
Removing the Mini PCI Card 1. Disconnect the antenna cable from the Mini PCI card. 2. Release the Mini PCI card by spreading the metal securing
Back to Contents Page Before You Begin Dell™X200ServiceManual Preparing to Work Inside the Computer Recommended Tools Computer Orientation
Screw Identification When you are removing and replacing components, photocopy the placemat as a tool to lay out and keep track of the screws. The p
Back to Contents Page Modem Daughter Card: (1 each) Cooling Fan: (4 each) Speaker: (1 each)
Back to Contents Page Flashing the BIOS Dell™X200ServiceManual To update the basic input/output system (BIOS): 1. Go to support.dell.com. If th
Back to Contents Page Hinge Covers and Display Assembly Dell™X200ServiceManual Hinge Covers Display Assembly Hinge Covers Removing the Hinge
4. Turn the computer over, and remove the two M3 x 5-mm screws from the bottom of the computer. 5. Turn the computer over, and open the displa
Commenti su questo manuale