Dell S60 Guida di Installazione

S60 Quick Start GuideFTOS version 8.3.3.1 July 30, 2010

6 Hardware InstallationInsert Optional ModulesThe S60 system has expansion slots at the front left and the rear right of the chassis, that can be used

S60 Quick Start Guide 7Install the SFP and SFP+ opticsThe S60 has 4 SFP optical ports in the front of the chassis in addition to the optional SFP+ opt

8 Hardware InstallationSupply power and power up the systemSupply power to the S60 after they are mounted in a rack (or on a table) and the optional m

S60 Quick Start Guide 9This document is intended to aid you with quick installation and set-up of a new S60 system.• For complete information regardin

10 Getting StartedFigure 1 S60 serial console port connectorTo access the console port, follow the procedures below. Refer to Table 1 for the consol

S60 Quick Start Guide 11Access the USB-B console portThe S60 has 2 management ports available for system access: a console port and a USB-B port. The

12 Getting Started7 Using the terminal settings shown here, set the terminal connection settings.• 9600 baud rate, No parity, 8 data bits, 1 stop bit,

S60 Quick Start Guide 13Figure 3 Completed Boot ProcessDefault ConfigurationA version of FTOS is pre-loaded onto the chassis, however the system is

14 Getting StartedConfigure a Host NameThe host name appears in the prompt. The default host name is force10.• Host names must start with a letter and

S60 Quick Start Guide 151. Configure an IP address for the management port. See Configure the Management Port IP Address. 2. Configure a management ro

Copyright 2010 Force10 NetworksAll rights reserved. Printed in the USA. January 2010.Force10 Networks® reserves the right to change, modify, revise th

16 Getting StartedTo configure a username and password:Access the S-Series Remotely ( on a non-management port)The S-Series does not have a dedicated

S60 Quick Start Guide 17Figure 5 Configuring the S-Series for Remote AccessConfigure the Enable PasswordAccess the EXEC Privilege mode using the ena

18 Getting StartedThe E-Series EtherScale platform architecture uses MMC cards for both the internal and external Flash memory. MMC cards support a ma

S60 Quick Start Guide 19Important Points to Remember• You may not copy a file from one remote system to another.• You may not copy a file from one loc

20 Getting StartedView FilesFile information and content can only be viewed on local file systems.To view a list of files on the internal or external

S60 Quick Start Guide 21Figure 8 Viewing a List of Files in the Internal FlashTo view the contents of a file:View Configuration FilesConfiguration f

22 Getting StartedFigure 9 Tracking Changes with Configuration CommentsFile System ManagementThe Force10 system can use the internal Flash, external

S60 Quick Start Guide 23Figure 11 Alternative Storage LocationView command historyThe command-history trace feature captures all commands entered by

24 Getting Started

S60 Quick Start Guide 1Chapter 1S60 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2 Table of ContentsConfigure a Username and Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Access the

S60 Quick Start Guide 1This document is intended to aid you with quick installation and set-up of a new S60 system.• For complete S60 installation inf

2 S60 OverviewFeaturesThe S60 offers the following:• S60 CPU and switch processor• Stackable switch features• 19-inch rack-mountable• Standard 1U chas

S60 Quick Start Guide 3This document is intended to aid you with quick installation and set-up of a new S60 system.• For complete S60 installation inf

4 Hardware InstallationInstall the S60 chassis in a rack or cabinetAttach mounting bracketsThe S60 is shipped with mounting brackets (rack ears) and r

S60 Quick Start Guide 5Install chassis into rack or cabinetEnsure that there is adequate clearance surrounding the rack or within the cabinet to permi