Dell PowerVault DL2100 Manuale Utente

Dell™ PowerVault™DL2100 SystemsHardware Owner’sManual

10 Contents6 Jumpers and Connectors . . . . . . . . . . . 169System Board Jumpers . . . . . . . . . . . . . . . . . 169System Board Connectors. .

100 Installing System ComponentsFigure 3-14. Removing and Installing the Cooling FanReplacing a Cooling Fan1Align the fan plug with the connector at t

Installing System Components 101support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow

102 Installing System ComponentsReplacing the Fan Bracket1Align the fan bracket down onto the bracket base so that the mounting pins fit correctly int

Installing System Components 103support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow

104 Installing System ComponentsFigure 3-16. Removing and Installing the Optical Drive1 optical drive 2 optical-drive interface cable3 power cable 4 o

Installing System Components 105Figure 3-17. Routing the Optical Drive Cable Integrated Storage Controller CardYour system includes a dedicated expans

106 Installing System ComponentsRemoving the Integrated Storage Controller Card CAUTION: Many repairs may only be done by a certified service technic

Installing System Components 107Figure 3-18. Installing a Storage Controller Card3Slide the storage controller’s card edge connector into the card slo

108 Installing System Components6If not already done, route the interface and RAID battery cables in the cable path inside the right interior wall of

Installing System Components 109RAID BatteryThe information in this section applies only to systems with the optional PERC controller card.Removing a

About Your System 11About Your SystemAccessing System Features During StartupThe following keystrokes provide access to system features during startup

110 Installing System ComponentsFigure 3-20. Removing or Installing the RAID Battery1 RAID battery 2 RAID battery cable from storage controller3 batte

Installing System Components 111Cable RoutingCables that extend through the system front-to-back are routed along a cable path within the interior rig

112 Installing System ComponentsInstalling the Cable Retention Bracket1Insert the hooks and tabs of the cable retention bracket into the slots in the

Installing System Components 113• When the optional x16-link riser is installed, slot 4 is not available.• The expansion-card slots are not hot-swappa

114 Installing System Components NOTE: The procedure for installing expansion cards into risers 1 and 2 is the same except that slots 3 and 4 on rise

Installing System Components 115Removing an Expansion Card CAUTION: Many repairs may only be done by a certified service technician. You should only

116 Installing System ComponentsFigure 3-22. Removing or Installing the Expansion CardRemoving Expansion-Card Riser 1 CAUTION: Many repairs may only

Installing System Components 1172Open the system. See Opening the System.3Disconnect all cables connected to the expansion card.4Remove all expansion

118 Installing System ComponentsFigure 3-23. Removing and Replacing Expansion-Card Riser 1Removing Expansion-Card Riser 2 CAUTION: Many repairs may o

Installing System Components 1191Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.2Open t

12 About Your SystemFront Panel Features and IndicatorsFigure 1-1. Front Panel Features and Indicators Item Indicator, Button, or ConnectorIcon Descri

120 Installing System ComponentsFigure 3-24. Removing and Replacing Expansion-Card Riser 2Removing Expansion-Card Riser 2 From the Expansion-Card Brac

Installing System Components 121Figure 3-25. Removing and Replacing the Riser 2 Board5Remove the expansion-card riser board:aUsing a Phillips screwdri

122 Installing System Components4Reinstall expansion-card riser 2. See "Replacing Expansion-Card Riser 2."5Install all expansion cards in th

Installing System Components 123• In a dual-processor configuration, the memory configuration for each processor must be identical.• Memory modules of

124 Installing System ComponentsMode-Specific GuidelinesThree memory channels are allocated to each processor. The number of channels and allowable co

Installing System Components 125Table 3-2. Sample RDIMM Single- and Dual-Rank Memory Configurations (Per Processor)Memory ModeMemory Module SizeMemory

126 Installing System ComponentsAdvanced ECC2 2-GB vacant XXXXXXXXXXXX4812all 81624all4-GB vacant XXXXXXXXXXXX81624all 163248all8-GB1vacant XXXXXXXXXX

Installing System Components 127Table 3-3. Sample UDIMM Memory Configurations (Per Processor)Installing Memory Modules WARNING: The memory modules ar

128 Installing System Components1Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.2Open t

Installing System Components 129When the memory module is properly seated in the socket, the ejectors on the memory module socket align with the eject

About Your System 132 Power-on indicator, power buttonThe power-on indicator lights when the system power is on.The power button controls the DC power

130 Installing System Components3Remove the cooling shroud. See "Removing the Cooling Shroud."4Locate the memory module sockets. See Figure

Installing System Components 131 CAUTION: Never remove the heat sink from a processor unless you intend to remove the processor. The heat sink is nec

132 Installing System Components CAUTION: The processor is held in its socket under strong pressure. Be aware that the release lever can spring up su

Installing System Components 133If you are permanently removing the processor, you must install a processor blank and a heat-sink blank in the CPU2 so

134 Installing System Components7Install the processor in the socket. Keep the processor level (see Figure 3-29) and insert it straight down into the

Installing System Components 13510Rotate the socket-release lever down until it snaps into place.Figure 3-30. Closing the Processor Shield11Install th

136 Installing System Components12Replace the cooling shroud. See "Installing the Cooling Shroud."13Close the system. See "Closing the

Installing System Components 137bPress the battery toward the positive side of the connector and lift it up out of the securing tabs at the negative s

138 Installing System ComponentsControl Panel Assembly NOTE: The control panel assembly consists of two separate modules—the display module and the

Installing System Components 139Figure 3-32. Removing and Installing the Control PanelRemoving the Control Panel Board CAUTION: Many repairs may only

14 About Your SystemLCD Panel FeaturesThe system's LCD panel provides system information and status messages to signify when the system is operat

140 Installing System Components1Turn off the system and attached peripherals, and disconnect the system from the electrical outlet and peripherals.2O

Installing System Components 141SAS BackplaneRemoving the SAS Backplane CAUTION: Many repairs may only be done by a certified service technician. You

142 Installing System ComponentsFigure 3-33. Removing and Installing the SAS BackplaneInstalling a SAS Backplane1Lower the backplane into the system,

Installing System Components 1433Slide the backplane downward until the blue retention latch locks into place. 4Connect the SAS data and power cables

144 Installing System Components7Remove the two riser boards. See "Removing Expansion-Card Riser 1" and "Removing Expansion-Card Riser

Installing System Components 145Figure 3-34. System Board RemovalInstalling the System Board1Unpack the new system board and remove the label placard

146 Installing System ComponentscPush the system board toward the back of the chassis until the blue retention pin locks into place. 6If applicable, t

Troubleshooting Your System 147Troubleshooting Your SystemSafety First—For You and Your System CAUTION: Many repairs may only be done by a certified

148 Troubleshooting Your SystemTroubleshooting the Video Subsystem 1Check the system and power connections to the monitor.2Check the video interface c

Troubleshooting Your System 1494Reconnect and power on each USB device one at a time.5If a device causes the same problem, power down the device, repl

About Your System 15Figure 1-2. LCD Panel FeaturesHome ScreenThe Home screen displays user-configurable information about the system. This screen is d

150 Troubleshooting Your System4Ensure that the appropriate drivers are installed and the protocols are bound. See the NIC's documentation.5Enter

Troubleshooting Your System 151• Power supplies• Processors and heat sinks• Memory modules• Fan bracket4Let the system dry thoroughly for at least 24

152 Troubleshooting Your System• Memory modules• Hard-drive carriers4Ensure that all cables are properly connected.5Close the system. See "Closin

Troubleshooting Your System 153 CAUTION: If troubleshooting a power supply mismatch error, replace only the power supply with the flashing indicator.

154 Troubleshooting Your System• An individual cooling fan is removed or has failed. See "Troubleshooting a Fan."Troubleshooting a Fan CAUT

Troubleshooting Your System 155If diagnostics indicates a fault, follow the corrective actions provided by the diagnostic program.2If the system is no

156 Troubleshooting Your System16Remove the cooling shroud. See "Removing the Cooling Shroud."17If a diagnostic test or error message indica

Troubleshooting Your System 1576Close the system. See "Closing the System."7Turn on the system and attached peripherals and check if the SD

158 Troubleshooting Your System10Turn on the system and attached peripherals and check if the USB key is functioning.If the problem is not resolved, s

Troubleshooting Your System 159Troubleshooting a Hard Drive CAUTION: Many repairs may only be done by a certified service technician. You should only

16 About Your SystemFrom the Home screen, press the Select button to enter the main menu. See the following tables for information on the Setup and Vi

160 Troubleshooting Your SystemTroubleshooting a Storage Controller. NOTE: When troubleshooting a SAS or PERC controller, also see the documentation f

Troubleshooting Your System 16110Ensure that the cables are firmly connected to the storage controller and the SAS backplane board.11Close the system.

162 Troubleshooting Your System10Remove all expansion cards installed in the system. See "Removing an Expansion Card."11Reseat the expansion

Troubleshooting Your System 1635Ensure that each processor and heat sink are properly installed. See "Installing a Processor."6Replace the c

164 Troubleshooting Your System

Running the System Diagnostics 165Running the System DiagnosticsIf you experience a problem with your system, run the diagnostics before calling for t

166 Running the System Diagnostics• Display, print, or save test results• Temporarily suspend testing if an error is detected or terminate testing whe

Running the System Diagnostics 167Embedded System Diagnostics Testing OptionsClick the testing option in the Main Menu window.Using the Custom Test Op

168 Running the System Diagnostics•Test Iterations — Selects the number of times the test is run.•Log output file pathname — Enables you to specify th

Jumpers and Connectors 169Jumpers and Connectors CAUTION: Many repairs may only be done by a certified service technician. You should only perform tr

About Your System 17Hard-Drive Indicator Patterns for RAIDFigure 1-3. Hard-Drive IndicatorsPower Displays the power output of the system in BTU/hr or

170 Jumpers and ConnectorsFigure 6-1. System Board JumpersJumper Setting DescriptionPWRD_EN Pins 2 and 4(default)The password feature is enabled.Pins

Jumpers and Connectors 171Pins 1 and 3 The configuration settings are cleared at the next system boot. If the configuration settings become corrupted

172 Jumpers and ConnectorsSystem Board ConnectorsFigure 6-2. System Board ConnectorsConnector Description1 RISER2 expansion-card riser 2 connector2 RI

Jumpers and Connectors 1733 iDRAC6 iDRAC6 Enterprise card connector4 SATA_A SATA A connector5 SATA_B SATA B connector6B1B4B7B2B5B8B3B6B9memory module

174 Jumpers and Connectors19 A1A4A7A2A5A8A3A6A9memory module slot A1(white release lever)memory module slot A4memory module slot A7memory module slot

Jumpers and Connectors 175SAS Backplane Board ConnectorsFigure 6-3. SAS Backplane Board (6 Slots)1 drive 1 connector 2 drive 0 connector3 drive 3 conn

176 Jumpers and ConnectorsExpansion-Card Riser-Board Components and PCIe BusesFigure 6-4. PCIe Expansion-Card Riser 1 Components1 slot 1 PCIe - x4 lin

Jumpers and Connectors 177Figure 6-5. Standard PCIe Expansion-Card Riser 2 Components1 chassis intrusion switch 2 screw3 slot 3 PCIe x8 link (full-hei

178 Jumpers and ConnectorsFigure 6-6. Optional PCIe x16 Expansion-Card Riser 2 ComponentsDisabling a Forgotten PasswordThe system's software secu

Jumpers and Connectors 179See Figure 6-1 to locate the password jumper (labeled "PWRD_EN") on the system board.4Close the system. See "

18 About Your SystemBack Panel Features and IndicatorsFigure 1-4. Back Panel FeaturesDrive-Status Indicator Pattern (RAID Only)ConditionBlinks green t

180 Jumpers and Connectors

Getting Help 181Getting HelpContacting DellFor customers in the United States, call 800-WWW-DELL (800-999-3355). NOTE: If you do not have an active

182 Getting Help

Glossary 183GlossaryA — Ampere(s).AC — Alternating current.ACPI — Advanced Configuration and Power Interface. A standard interface for enabling the op

184 GlossaryCPU — Central processing unit. See processor.DC — Direct current.DDR — Double-data rate. A technology in memory modules that potentially d

Glossary 185flash memory — A type of electronic chip that can be programmed and reprogrammed using a software utility.FTP — File transfer protocol.g —

186 GlossaryKB — Kilobyte(s); 1024 bytes.Kbps — Kilobit(s) per second.KBps — Kilobyte(s) per second.kg — Kilogram(s); 1000 grams.kHz — Kilohertz.KVM —

Glossary 187memory — An area in your system that stores basic system data. A system can contain several different forms of memory, such as integrated

188 GlossaryPDU — Power distribution unit. A power source with multiple power outlets that provides electrical power to servers and storage systems in

Glossary 189SAS — Serial-attached SCSI.SATA — Serial Advanced Technology Attachment. A standard interface between the system board and storage devices

About Your System 19Item Indicator, Button, or ConnectorIcon Description1 PCIe slot 1 PCI Express (Generation 2) x4-link expansion slot (full-height,

190 GlossaryTB — Terabyte(s); 1024 gigabytes or 1,099,511,627,776 bytes. However, when referring to hard-drive capacity, the term is usually rounded t

Glossary 191a specific graphics resolution, you must install the appropriate video drivers and your monitor must support the resolution.virtualization

192 Glossary

Index 193IndexAAdvanced ECC memory mode, 124Bback panel features, 18backplaneSee SAS backplane.battery (RAID)installing, 109removing, 109battery (syst

194 Indexcoverclosing, 78opening, 78Ddamaged systemstroubleshooting, 151Dellcontacting, 181diagnosticsadvanced testing options, 167testing options, 16

Index 195heat sink, 131hot-swapcooling fans, 99hard drives, 80power supplies, 85IiDRAC Configuration Utility, 73iDRAC6 Enterprise cardinstalling, 93re

196 IndexLCD panelfeatures, 14menus, 15Mmemorytroubleshooting, 154Memory Mirroring memory mode, 124memory modeAdvanced ECC, 124Memory Mirroring, 124Op

Index 197troubleshooting, 152power supply blank, 87processorinstalling, 133removing, 130troubleshooting, 162upgrades, 130PSUSee power supply.RRAID bat

198 Indexserial connector, 20service-only procedurescontrol panel assembly, 138SAS backplane, 141system board, 143setup password, 72SSD hard drives, 8

Index 199UUEFI Boot Managerentering, 68main screen, 69System Utilities screen, 69UEFI Boot Settings screen, 69UEFI boot mode, 55upgradesprocessor, 130

Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indica

20 About Your SystemPower Indicator CodesAn LED indicator on the power button indicates when power is supplied to the system and the system is operati

200 Index

About Your System 21Figure 1-5. Power Supply Status IndicatorNIC Indicator CodesFigure 1-6. NIC Indicators1 power supply status1 link indicator 2 acti

22 About Your SystemLCD Status MessagesThe LCD messages consist of brief text messages that refer to events recorded in the System Event Log (SEL). Fo

About Your System 23Table 1-1. LCD Status MessagesCode Text Cause Corrective ActionsE1000 Failsafe voltage error. Contact support.Check the system eve

24 About Your SystemE1229 CPU # VCORE Regulator failure. Reseat CPU.Specified processor VCORE voltage regulator has failed.Reseat the processor(s). Se

About Your System 25E1313 Fan redundancy lost. Check fans.The system is no longer fan redundant. Another fan failure would put the system at risk of o

26 About Your SystemE1420 CPU Bus parity error. Power cycle AC.The system BIOS has reported a processor bus parity error.Remove AC power to the system

About Your System 27E1620 Power Supply # (### W) AC power error. Check PSU cables.Specified power supply's AC input is outside of the allowable r

28 About Your SystemE1711 PCI parity error on Bus ## Device ## Function ##The system BIOS has reported a PCI parity error on a component that resides

About Your System 29E1715 Fatal I/O Error. Review & clear SEL.The system BIOS has determined there has been a fatal error in the system.Check the

Contents 3Contents1 About Your System . . . . . . . . . . . . . . . . . 11Accessing System Features During Startup . . . . . . 11Front Panel Feat

30 About Your SystemE171F PCIe fatal error on Bus ## Device ## Function ##The system BIOS has reported a PCIe fatal error on a component that resides

About Your System 31E1A14 SAS cable A failure. Check connection.SAS cable A is missing or bad.Reseat the cable. If the problem persists, replace cable

32 About Your SystemE2014 CMOS RAM failure. Power cycle AC.CMOS failure. CMOS RAM not functioning properly.Remove AC power to the system for 10 second

About Your System 33E201A SuperIO failure. Power cycle AC.SIO failure. Remove AC power to the system for 10 seconds and restart the system. If the pro

34 About Your SystemE2022 General failure during POST. Check screen message.General failure after video. Check screen for specific error messages. E20

About Your System 35I1911 LCD Log Full. Check SEL to review all Errors.LCD overflow message. A maximum of ten error messages can display sequentially

36 About Your SystemSystem MessagesSystem messages appear on the screen to notify you of a possible problem with the system. NOTE: If you receive a s

About Your System 37Alert! iDRAC6 not responding. Rebooting.The iDRAC6 is not responding to BIOS communication either because it is not functioning pr

38 About Your SystemAlert! Power required exceeds PSU wattage. Check PSU and system configuration. Alert! Continuing system boot accepts the risk that

About Your System 39BIOS Update Attempt Failed!Remote BIOS update attempt failed.Retry the BIOS update. If problem persists, see "Getting Help.&q

4 Contents2 Using the System Setup Program and UEFI Boot Manager 55Choosing the System Boot Mode . . . . . . . . . . . . 55Entering the System Set

40 About Your SystemCurrent boot mode is set to UEFI. Please ensure compatible bootable media is available. Use the system setup program to change the

About Your System 41Gate A20 failure Faulty keyboard controller; faulty system board.See "Getting Help."General failure The operating system

42 About Your SystemLocal keyboard may not work because all user accessible USB ports are disabled. If operating locally, power cycle the system and e

About Your System 43Memory odd/even logic failure at address, read value expecting valueFaulty or improperly installed memory modules.See "Troubl

44 About Your SystemNo boot device availableFaulty or missing optical drive subsystem, hard drive, or hard-drive subsystem, or no bootable USB key ins

About Your System 45Plug & Play Configuration ErrorError encountered in initializing PCIe device; faulty system board.Install the NVRAM_CLR jumper

46 About Your SystemSATA port x device auto-sensing errorSATA port x device configuration errorSATA port x device errorThe drive connected to the spec

About Your System 47The following DIMMs should match in geometry: x,x,...Invalid memory configuration. The specified memory modules do not match in si

48 About Your SystemTimer chip counter 2 failedFaulty system board. See "Getting Help."TPM configuration operation honored. System will now

About Your System 49Unable to launch System Services image. System halted!System halted after F10 keystroke because System Services image is either co

Contents 5iDRAC Configuration Utility . . . . . . . . . . . . . . . 73Entering the iDRAC Configuration Utility. . . . . . 743 Installing System Co

50 About Your SystemUnused memory detected. DIMM’s installed in the following slot are not available when in mirror or 128-bit advanced ECC modes: x,x

About Your System 51Warning! Power required exceeds PSU wattage. Check PSU and system configuration. Warning! Performance degraded. CPU and memory set

52 About Your SystemWarning MessagesA warning message alerts you to a possible problem and prompts you to respond before the system continues a task.

About Your System 53Other Information You May Need WARNING: See the safety and regulatory information that shipped with your system. Warranty informa

54 About Your System

Using the System Setup Program and UEFI Boot Manager 55Using the System Setup Program and UEFI Boot ManagerThe System Setup program is the BIOS progra

56 Using the System Setup Program and UEFI Boot ManagerEntering the System Setup Program1Turn on or restart your system.2Press <F2> after you se

Using the System Setup Program and UEFI Boot Manager 57System Setup OptionsMain ScreenFigure 2-1. Main System Setup Program Screen NOTE: The options f

58 Using the System Setup Program and UEFI Boot ManagerSATA Settings Displays a screen to enable or disable the integrated SATA controller and ports.

Using the System Setup Program and UEFI Boot Manager 59Memory Settings ScreenF1/F2 Prompt on Error(Enabled default)Enables the system to halt on error

6 ContentsInstalling the Power Supply Blank . . . . . . . . . 87Internal SD Module . . . . . . . . . . . . . . . . . . . 87Installing the Internal

60 Using the System Setup Program and UEFI Boot ManagerProcessor Settings ScreenSATA Settings ScreenOption Description64-bit Specifies if the processo

Using the System Setup Program and UEFI Boot Manager 61Boot Settings ScreenPort B(Off default)Auto enables BIOS support for the device attached to SAT

62 Using the System Setup Program and UEFI Boot ManagerIntegrated Devices ScreenBoot Sequence Retry(Disabled default)If this field is enabled and the

Using the System Setup Program and UEFI Boot Manager 63PCI IRQ Assignments ScreenSerial Communication ScreenOS Watchdog Timer(Disabled default)Sets a

64 Using the System Setup Program and UEFI Boot ManagerEmbedded Server Management ScreenSerial Port Address(Serial Device 1=COM1, Serial Device2=COM2

Using the System Setup Program and UEFI Boot Manager 65Power Management ScreenOption DescriptionPower Management Options are OS Control, Active Power

66 Using the System Setup Program and UEFI Boot ManagerSystem Security ScreenOption DescriptionSystem Password Displays the current status of the pass

Using the System Setup Program and UEFI Boot Manager 67Exit ScreenPress <Esc> to exit the System Setup program; the Exit screen displays:• Save

68 Using the System Setup Program and UEFI Boot ManagerEntering the UEFI Boot Manager NOTE: Operating systems must be 64-bit UEFI-compatible (for exa

Using the System Setup Program and UEFI Boot Manager 69UEFI Boot Manager ScreenUEFI Boot Settings ScreenSystem Utilities ScreenOption DescriptionConti

Contents 7Integrated Storage Controller Card . . . . . . . . . . . 105Removing the Integrated Storage Controller Card . . . . . . . . . . . . . . . .

70 Using the System Setup Program and UEFI Boot ManagerSystem and Setup Password Features NOTE: For a forgotten password, see "Disabling a Forgo

Using the System Setup Program and UEFI Boot Manager 712Highlight the System Password option and press <Enter>. 3Type your new system password.

72 Using the System Setup Program and UEFI Boot ManagerIf an incorrect system password is entered, the system displays a message and prompts you to re

Using the System Setup Program and UEFI Boot Manager 73The password assignment is not case-sensitive. To erase a character, press <Backspace> or

74 Using the System Setup Program and UEFI Boot Manager• Enable a LAN Platform Event Trap (PET) destination.• Attach or detach the Virtual Media devic

Installing System Components 75Installing System ComponentsRecommended Tools• Key to the system keylock• #1 and #2 Phillips screwdrivers• Wrist ground

76 Installing System ComponentsFigure 3-1. Inside the System 1 USB connector for optional internal USB key2 Internal SD Module3 RAID battery (optional

Installing System Components 77Front Bezel (Optional)A lock on the bezel restricts access to the power button, optical drive, and hard drive(s). The L

78 Installing System ComponentsInstalling the Front Bezel1Insert the hinge tab on the right of the bezel into the slot on the right side of the system

Installing System Components 79Figure 3-3. Removing or Installing the CoverInformation TagRemoving the Information Tag1Pull the information tag out of

8 ContentsInstalling a Processor . . . . . . . . . . . . . . . 133System Battery. . . . . . . . . . . . . . . . . . . . . . 136Replacing the System

80 Installing System ComponentsFigure 3-4. Removing the Information TagInstalling the Information Tag1Align the information tag with the slot on the c

Installing System Components 81 CAUTION: Do not turn off or reboot your system while the drive is being formatted. Doing so can cause a drive failure

82 Installing System ComponentsRemoving a Hot-Swap Hard Drive CAUTION: Ensure that your operating system supports hot-swap drive removal and installa

Installing System Components 83Figure 3-6. Installing the Hot-Swap Hard Drive3Install the hot-swap hard drive.aPress the button on the front of the dr

84 Installing System Components3 Attach the four screws to secure the hard drive to the hard-drive carrier. Figure 3-7. Installing the Hard Drive into

Installing System Components 85Power SuppliesYour system supports the following power supply modules:• 570-W Energy Smart power supply• 870-W High Out

86 Installing System ComponentsFigure 3-8. Removing and Installing the Power SupplyReplacing a Power Supply1On a system with redundant power supplies,

Installing System Components 87 NOTE: When installing, hot-swapping, or hot-adding a new power supply, allow several seconds for the system to recogn

88 Installing System ComponentsFigure 3-9. Removing or Installing the Internal SD Module4Connect the internal SD module cable to the connector on the

Installing System Components 89Removing the Internal SD Module CAUTION: Many repairs may only be done by a certified service technician. You should o

Contents 9Troubleshooting the System Battery . . . . . . . . . . 152Troubleshooting Power Supplies. . . . . . . . . . . . 152Troubleshooting System

90 Installing System Components3 Locate the SD card connector on the internal SD module and, with the label side facing up, insert the contact-pin end

Installing System Components 91 CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and

92 Installing System ComponentsInternal USB CableRemoving the Internal USB Cable1Turn off the system, including any attached peripherals, and disconne

Installing System Components 93iDRAC6 Enterprise Card (Optional)The optional Integrated Dell™ Remote Access Controller 6 (iDRAC6) Enterprise card prov

94 Installing System ComponentsFigure 3-11. Removing and Installing the iDRAC6 Enterprise CardRemoving an iDRAC6 Enterprise Card CAUTION: Many repair

Installing System Components 956Remove the iDRAC6 Enterprise card: aPull back slightly on the two tabs at the front edge of the card and gently lift t

96 Installing System Components CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and

Installing System Components 976Reconnect the system to the electrical outlet and turn on the system and attached peripherals.Cooling ShroudThe system

98 Installing System ComponentsFigure 3-13. Removing and Installing the Cooling ShroudInstalling the Cooling Shroud1Align the tabs on the right side o

Installing System Components 99Cooling FansThe system has either five or four hot-swappable fans to provide cooling to the system’s interior component