Dell OpenManage Integration for VMware vCenter 2.1 Manuale Utente Pagina 174
- Pagina / 194
- Indice
- RISOLUZIONE PROBLEMI
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
When I tried to use lockdown mode, it failed.
When I added a host to the connection profile in lockdown mode, the inventory kicked off but failed stating that “No
Remote Access Controller was found or Inventory is not supported on this host.” Inventory is supposed to work for a
host in lockdown mode, right?
If you put the host in lockdown mode or remove a host from lockdown mode, you must wait 30–minutes before
performing the next operation on the OpenManage Integration for VMware vCenter.
What Setting Should I Use For UserVars.CIMoeMProviderEnable With ESXi 4.1 U1?
Set UserVars.CIMoemProviderEnabled to 1.
I Am Using A Reference Server to Create a Hardware Profile But it Failed. What Should I
Do?
Check to make sure that minimum recommended versions of iDRAC firmware, Lifecycle Controller firmware, and BIOS
are installed.
To make sure that the data retrieved from the reference server is current, enable Collect System Inventory On Restart
(CSIOR), and restart the reference server prior to extraction of data.
I Am Attempting to Deploy ESX/ESXi on a Blade Server and it Failed. What Should I Do?
1. Make sure the ISO location (NFS path) and staging folder paths are accurate.
2. Make sure the NIC selected during assignment of server identity is on the same network as the virtual appliance.
3. If using static IP address, make sure the network information provided (including subnet mask and default gateway)
is accurate. In addition, , make sure the IPaddress is not already assigned on the network.
4. Make sure at least one Virtual Disk is seen by the system. ESXi also installs to an internal RIPS SD card.
Why are My Hypervisor Deployments Failing on my Dell PowerEdge R210 II Machines?
A timeout issue on Dell PowerEdge R210 II systems produces a hypervisor deployment failure error due to the failure of
the BIOS to boot from the attached ISO. To resolve this issue, manually install hypervisor on the machine.
Why Do I See Auto-discovered Systems Without Model Information in the Deployment
Wizard
This usually indicates that the firmware version installed on the system does not meet recommended minimum
requirements. In some cases, a firmware update may not have registered on the system. Cold booting the system or
reseating the blade fixes this problem. The newly enabled account on the iDRAC must be disabled and auto-discovery
reinitiated to provide model information and NIC information to the OpenManage Integration for VMware vCenter.
The NFS Share is Set Up With the ESX/ESXI ISO, but Deployment Fails with Errors
Mounting the Share Location.
To find the solution:
1. Make sure the iDRAC is able to ping the appliance.
2. Make sure your network is not running too slow.
3. Make sure the ports: 2049, 4001 - 4004 are open and the firewall is set accordingly.
174
- Web Client 1
- User's Guide Version 2.1 1
- Notes, Cautions, and Warnings 2
- Contents 3
- Introduction 11
- Inside the VMware vCenter 19
- Understanding Icon Buttons 19
- Locating the Software Version 20
- Refreshing the Screen Content 20
- Licensing Tab 20
- Opening Online Help 21
- Finding Help and Support 21
- Soft iDRAC Reset 22
- Profiles 25
- Creating A Connection Profile 26
- Editing a Connection Profile 28
- Deleting A Connection Profile 30
- Testing a Connection Profile 30
- Viewing Chassis Profiles 30
- Editing a Chassis Profile 31
- Creating A Chassis Profile 31
- Deleting Chassis Profiles 32
- Testing a Chassis Profile 32
- Job Queue 33
- Warranty History 35
- About Logs 37
- Viewing the Logs 38
- Exporting Log Files 38
- Virtual Appliance Management 41
- Settings 51
- About Firmware Updates 53
- User’s Guide 55
- Viewing Events 60
- Chassis Management 75
- Viewing Warranty Details 80
- Viewing Storage 81
- Monitoring a Single Host 85
- Launching Management Consoles 88
- Launching the OMSA Console 89
- Buy License 91
- Single Host 95
- Renewing Host Warranty 117
- Clusters 123
- Datacenters or Clusters 129
- Datacenters and Clusters 131
- OpenManage 142
- This means cache I/O 147
- • Disabled 147
- This means direct I/O 147
- • Enabled 147
- Console Administration 155
- VMware vCenter 156
- Setting Up The HTTP Proxy 158
- Setting Up the NTP Servers 158
- Setting up Global Alerts 160
- Managing Backup And Restore 160
- Scheduling Automatic Backups 161
- Configuring Network Settings 162
- Setting The Local Time Zone 163
- Rebooting Virtual Appliance 163
- Refreshing the Console View 164
- Read-only User Role 164
- Troubleshooting 165
- Dell Management Plug-in 169
- Table 5. Managed Nodes 170
- Clusters page? 172
- Bare Metal Deployment Issues 176
- Contacting Dell 177
- Virtualization—Related Events 179
- Data Integrity 185
- Dell Operation Role 187
- Understanding Privileges 189
- Understanding Auto-Discovery 191
- Auto-Discovery 192
Prodotti e manuali riguardandi Networking Dell OpenManage Integration for VMware vCenter 2.1
Networking Dell N2000 Modalità d'Uso
(21 pagine)
(21 pagine)
Networking Dell UPS 1920R Guida Utente
(9 pagine)
(9 pagine)
Networking Dell SupportAssist Version 1.2.1 For OpenManage Essentials Manuale di Avvio Rapido
(10 pagine)
(10 pagine)
Networking Dell PowerEdge 800 Manuale Utente
(27 pagine)
(27 pagine)
Networking Dell Chassis Management Controller Version 4.3 Guida alla Risoluzione dei Problemi
(10 pagine)
(10 pagine)
Networking Dell C521 Manuale Utente
(50 pagine)
(50 pagine)
(2 pagine)
Networking Dell Brocade 6505 Manuale Utente
(60 pagine)
(60 pagine)
© 2020, manymanuals.it. Tutti i diritti riservati | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale