Dell Force10 E300 Manuale di Installazione Pagina 1

Installing and Maintaining theE300 System

10 | The E300 Systemwww.dell.com | support.dell.comFigure 2-2. E300 Chassis Rear View with AC Power SuppliesFigure 2-3. E300 Chassis Rear View with

The E300 System | 11*With one SFM, the E300 does not transmit traffic at line rate.E300 System Installation ProcessTo install the E300 System, Dell Fo

12 | The E300 Systemwww.dell.com | support.dell.com

Site Preparation | 133Site PreparationThis chapter describes the requirements and procedures for installing your E300. The topics covered are:• “Site

14 | Site Preparationwww.dell.com | support.dell.comRack MountingWhen you prepare your equipment rack:• Make sure the rack is bolted to the floor and/

Site Preparation | 15If the E300 is connected to a 220 VAC power supply, two power supply modules are required; four power supply modules are required

16 | Site Preparationwww.dell.com | support.dell.comFans and AirflowYour E300 chassis contains one field-replaceable fan tray. Air flows through the E

Installing the Chassis | 174Installing the ChassisSafety Considerations WARNING: The E300 System is packaged in two separate containers. The chassis

18 | Installing the Chassiswww.dell.com | support.dell.comFigure 4-2. Rack Mounting the ChassisFor 19-inch mid mount and 23-inch mid mount brackets,

Installing Power Modules | 195Installing Power ModulesThis chapter contains the following major sections:• Installing AC Power Modules• Installing DC

Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indic

20 | Installing Power Moduleswww.dell.com | support.dell.comAC Power RequirementsAC Power Cord RequirementsEach AC power supply is shipped with a Dell

Installing Power Modules | 21Figure 5-1. AC Power Supply Locations The E300 contains four power supply slots in the rear of the chassis (Figure 5-1).

22 | Installing Power Moduleswww.dell.com | support.dell.comInstalling an AC Power SupplyTo install an AC power supply: NOTE: If there is a failure i

Installing Power Modules | 23Figure 5-2. DC PEM LocationsDC RequirementsRedundancyFor full facility redundancy, install two DC PEMs where each PEM mu

24 | Installing Power Moduleswww.dell.com | support.dell.comLED Status Removing a DC PEMThe left chassis PEM slot is labelled “0” and the right chassi

Installing Power Modules | 25Installing a DC PEM Figure 5-3. Removing the PEM Safety Cover Step Task 1 Turn the remote power source (the circuit brea

26 | Installing Power Moduleswww.dell.com | support.dell.com6 Secure the chassis ground connection: WARNING: You must complete the ground connection

Installing Power Modules | 27Power Supply and Fan Operability Test After you have completed the fan tray and power supply installation, verify their o

28 | Installing Power Moduleswww.dell.com | support.dell.com

Installing E300 Fan Tray | 296Installing E300 Fan Tray WARNING: To ensure proper temperature and airflow control, the fan tray must always be install

Contents | 3Contents1 About this GuideInformation Symbols and Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

30 | Installing E300 Fan Traywww.dell.com | support.dell.com

Installing RPMs, Line Cards, and SFMs | 317Installing RPMs, Line Cards, and SFMsThe E300 System accommodates six line cards, two Route Processor Modul

32 | Installing RPMs, Line Cards, and SFMswww.dell.com | support.dell.com WARNING: Do not supply power to your E300 system until the PEM and fan tray

Installing RPMs, Line Cards, and SFMs | 33%IRC-6-IRC_COMMUP: Link to peer RPM is up%RAM-6-RAM_TASK: RPM1 is in Standby State.Once the link between the

34 | Installing RPMs, Line Cards, and SFMswww.dell.com | support.dell.comLine Card LEDsLine card LEDs are described in the documentation specific to e

Installing RPMs, Line Cards, and SFMs | 35Figure 7-2. Using the Expandable Cable Management Bracket To use the cable management system: Installing Sw

36 | Installing RPMs, Line Cards, and SFMswww.dell.com | support.dell.comFigure 7-3. SFM Table 7-2 describes the SFM front panel and LEDs. Figure 7-4

Installing RPMs, Line Cards, and SFMs | 37To install SFMs: Step Task 1 Hold the card by the edges. Avoid touching the printed circuit board and connec

38 | Installing RPMs, Line Cards, and SFMswww.dell.com | support.dell.com

RPM Ports and Cables | 398RPM Ports and CablesThe RPM contains three ports, which are labeled and described as:• Console. A Universal Asynchronous Rec

4 | Contentswww.dell.com | support.dell.comBlank Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

40 | RPM Ports and Cableswww.dell.com | support.dell.comFigure 8-1. Pinouts for an RJ-45 Connector End of AdaptorsTable 8-1 displays the RJ-45 consol

RPM Ports and Cables | 41You can connect to the console using a RJ-45 to RJ-45 rollover cable and a RJ-45 to DB-9 female DTE adapter (labeled “TERMINA

42 | RPM Ports and Cableswww.dell.com | support.dell.comYou can access the auxiliary port using a dial-up modem using a RJ-45 to RJ-45 rollover cable

Powering Up | 439Powering UpThis chapter provides instructions for powering up your E300 system once you have installed all the chassis components and

44 | Powering Upwww.dell.com | support.dell.comTo turn the power off on the power modules, use one of the following methods:• On the DC PEMs, flip the

Removing and Replacing Components | 4510Removing and Replacing ComponentsThis section provides instructions for removing and replacing the following E

46 | Removing and Replacing Componentswww.dell.com | support.dell.comFigure 10-1. E300 Fan TrayTo remove and replace the fan tray:Removing and Replac

Removing and Replacing Components | 47To remove an AC Power Supply:Removing and Replacing RPMs, Line Cards, or SFMs WARNING: Your E300 system will no

48 | Removing and Replacing Componentswww.dell.com | support.dell.comTo remove and replace E300 RPMs and line cards: To remove and install an SFM:Remo

Removing and Replacing Components | 49Figure 10-2. Replacing the Air FilterTo remove and replace the air filter:Step Task1 Pull the air filter straig

Contents | 5D System SpecificationsChassis Physical Design. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

50 | Removing and Replacing Componentswww.dell.com | support.dell.com

System Boot | 51ASystem Boot When you supply power to the E300 system, the system performs a series of power-on self-tests. SFM, RPM, and line card St

52 | System Bootwww.dell.com | support.dell.com boot change {primary | secondary | default}If your configuration displays no preconfigured operating s

System Boot | 53 show bootvar This command displays the current operating system boot configuration parameters. show bootflash This command displays

54 | System Bootwww.dell.com | support.dell.comRefer to the <ItalicText>FTOS Command Line Interface Reference for BOOT_USER mode commands and co

The Compact Flash Card | 55BThe Compact Flash CardEach RPM is designed with a slot (slot0:) to accommodate a Compact Flash Card (external flash memory

56 | The Compact Flash Cardwww.dell.com | support.dell.comFormatting a Compact Flash Card New Compact Flash cards must be formatted in the E300 before

Alarms | 57CAlarmsThe E300 System generates major and minor alarms for the following conditions:• fan tray status• power supply status• RPMs status• h

58 | Alarmswww.dell.com | support.dell.comAC Power Supplies and AlarmsDuring system boot, if the redundant power supply (the fourth power supply) is m

System Specifications | 59DSystem SpecificationsThe major sections in this appendix are:• Chassis Physical Design• Environmental Parameters on page 60

6 | Contentswww.dell.com | support.dell.com

60 | System Specificationswww.dell.com | support.dell.comEnvironmental Parameters Power Supplies System Power RequirementsTable D-1. AC Power System

System Specifications | 61Module Power Requirements NOTE: Additional components may be available for your system, other than those included in the a

62 | System Specificationswww.dell.com | support.dell.comEuropean Community ContactDell Force10, EMEA - CentralDahlienweg 1966265 HeusweilerGermanyhtt

System Specifications | 63• EN 60825-2 Safety of Laser Products—Part 2: Safety of Optical Fibre Communication Systems• FDA Regulation 21CFR 1040.10 an

64 | System Specificationswww.dell.com | support.dell.comFigure D-1. The European WEEE symbol In accordance with the European WEEE Directive, electri

Technical Support | 65ETechnical Support This appendix contains these sections:• The iSupport Website• Contacting the Technical Assistance Center on p

66 | Technical Supportwww.dell.com | support.dell.comContacting the Technical Assistance CenterRequesting a Hardware ReplacementTo request replacement

Technical Support | 67Locating E300 Serial NumbersCurrently, in nearly all cases, the serial number has a two-letter preamble followed by nine digits,

68 | Technical Supportwww.dell.com | support.dell.comFigure E-1. Serial Number on Back of ChassisLine Card: The serial number of any E300 line card i

Technical Support | 69Figure E-3. Serial Number on Route Processor Module Power Supply: The serial number of the power supply module is located on th

About this Guide | 71About this GuideThis guide provides site preparation recommendations, step-by-step procedures for installing the Dell Force10 E30

70 | Technical Supportwww.dell.com | support.dell.comFigure E-6. Serial Number on Fan Tray R0R1 0 1 2 3 4 5 FanStatusCC-E300-FANSerial #Serial #Assy

Index | 71IndexAAC power suppliesinstalling 22air filterreplacing 48air flow 14, 16alarmsfan trays 45line cards 47PEMs 46relay contacts on RPM

72 | Indexwww.dell.com | support.dell.comRrackplacement 14recycling, switch 63removingair filters 48fan trays 46line cards 48PEMs 47RPMs 48SFMs

www.dell.com | support.dell.comPrinted in the U.S.A.

8 | About this Guidewww.dell.com | support.dell.com CAUTION: Wear grounding wrist straps when handling this equipment to avoid ESD damage. CAUTION:

The E300 System | 92The E300 SystemThe Dell Force 10 E300 System is a high performance, low cost switch/router. The eight-slot system contains two slo